Search results for:

dibs on these RO1s, pmd

Don't think cranks have any marking except length. But visually my RO1 is 'straighter' than RS7, so for a given axle and chainline the pedals are further apart on RS7 for MTB clearance
swap would work for me

just to chip in, have some spare RS7s that I could part with (do you need a spider?) ... if Amey sells me his RO2 set to replace them.
Amey, what was the answer to the sizing question - distance between crank arms?

and yes RO1, RO2 and RS7 all have different spiders, I have used several sets as there is nothing near as versatile for odd and fancy builds

dibs on this lot, pmd

Pmd about wheel

Still looking? I have a spare Minimal, 1 1/8th, 250ml steerer, excellent condition

Are they stickers on the wheel or printed ie can it be debadged?

I have an as new (one setup ride) cs9000 11-28, if that's close enough.
Not sure what changed 9000- 9100?

£350

Geometry

Look 585 frameset, size large , £350.
Includes full carbon Look seatpost, x3 Look headset spacers, and the headset bearings were recently changed. There is 61mm of steerer above the headset top cap.
If you are looking you probably know a bit about these classic frames already, one of the the later lugged carbon made in Never France (I think only the 595 came after, and then they moved to the monocoque type). It has been my 'Raid' bike for a few years, being light, very comfy, and the best descending bike I have yet had - several trips across the Alps and Pyrenees. Condition is good, only some marking of the lacquer and paint, as you would expect of course, but no damage to the carbon I can see. There are lots of images at:
https://www.flickr.com/photos/baznewpics/albums/72157666097988738
to show the condition as best I could.
If you want any further parts shown in the built up photos, just ask.

yes please pmd

pm for the Lake shoes

pmd for the tyres please

Look 595 frameset size L, £700 ono. Offered as frameset only (frame, 2xseatpost, fork and headset), but if anyone wants this full Ultegra build just ask.
I got this NOS about 2 years agao, and it's only been used for two trips in the Alps and some cafe rides locally, so condition is really excellent, just a few small marks in the clearcoat. There are detailed hires photos at ;
https://www.flickr.com/photos/baznewpics/albums/72157690378912955/with/26992980709/
But don't think any marks are gonna show up.

I did trim the ISP by about 30mm.
As built the BB to saddle top height is around 720mm. The Spesh saddle shown is only 40mm high and the saddle clamp is inverted (it's symetrical and reduces height by another 20mm). So the saddle will go up normally by 30mm if needed, with most saddles and flipping clamp. In addition you can add up to 30mm of elastomer spacers (included). The seatpost is reversible to give step TT/Tri position. I can also include 'standard' Look ergo post, with sliding clamp position if you need less layback. Also have other hard/soft elastomer and cutting guide, so the brave can make it shorter too.

pm sent for brakes

I'd take the Parlee clamp if Tom doesn't need it?

pm sent

Pm'd

ooh very tempted, would go to £300 (without case if that helps), otherwise I'm going to look for dealer tradein somewhere and get new one
cheers Barry

Now sold, thanks for everyone's interest

https://c1.staticflickr.com/5/4244/34717832426_95ae5031fb_b.jpg

Roberts Master Pro Compact frame, large, £500 ono, posted
Frameset including Easton superlite monocoque carbon fork, Campag record headset and seatclamp
hi-res pictures for detail/condition
https://www.flickr.com/photos/baznewpics/albums/72157680879889874
Roberts tubeset mix, front triangle Reynolds853Pro oversize (downtube 38mm thinwall, top tube tapered 32-29mm), rear triangle columbus ultra foco.
All perfectly smooth filet brazed and about as light as steel can get, Paint condition good, just a few touched up chips. All of the logos are done with masked in paint not transfers. Stainless steel CR headtube badge. Custom sizing of course, but as a guide this is setup for me at 5' 10", on compact frame, and BB axle to saddle top 72cm.
top tube , 554mm c-to-c, 570mm (virtual, horizontally headtube to seatpost)
seat tube, 480mm c-to-c, 520mm (centre axle to top of seat collar)
headtube, 160mm, chainstay, 410mm

It is still built at the moment, and the rest of the kit can be negotiated if wanted

pmd about the first set

now sold thanks mitch