Avatar for ARudd

ARudd

Member since Aug 2012 • Last active Aug 2021
  • 1 conversations
  • 7 comments

Most recent activity

    • 19 comments
    • 3,860 views
  • in Current Projects
    Avatar for ARudd

    Thanks joao24, I got a set of those break pads and they're completely silent!

    I thought it seemed like there was a bit too much excess on that cable but I only had random pictures of similar setups from the internet as a guide when cutting it. I'll consider shortening it when I get some time. The chain rings can't be separated unfortunately, I'll keep an eye out for a cheap replacement though it doesn't bother me too much.

    Here's a final picture with the charge saddle fitted and the bar angle tweaked a bit:

    Thanks for all your advice, help and criticism. It's been great fun to build and even more so to ride!

  • in Current Projects
    Avatar for ARudd

    Thanks Olly398!

    Never been a big fan of yellow or the team banana paint job as a whole, if the bike had been in good condition to start with then I might have kept it but as I was completely stripping it down anyway...

    First ride was great fun! Took a route around Cambridge city centre so as not to endanger too many pedestrians. The bike felt so smooth and responsive the seat was a bit of a ball ache but that's getting replaced as soon as the bracket I'm waiting on arrives. I'm using the original crank set with the chain on the smaller chainring (42T) and a 16T sprocket.

    I used the same brake/break pads as were on the previous wheels and any time I applied some pressure they'd screech horrendously (air horn volume). Is this just the pads adjusting to the new rims? Will it quiet down as they wear in?

    Didn't reface the headtube, is this likely to cause any problems?

  • in Current Projects
    Avatar for ARudd

    This will be my first expedition into the world of fixed gear bikes and also into the world of bike repair/maintenance as a whole.

    About a month ago I bought a Raleigh Team Banana through eBay. The initial plan was to keep it as a bit of an all purpose ride to get me to work and maybe a bit of leisure riding over the weekends.


    When I went to collect the bike it was in worse condition than I expected:
    -Wheels not true
    -rotten tyres and inner tubes.
    -heavily worn bottom bracket
    -rear derailer turned to scrap (chain had been running off the sprocket and had worn through most of the cage, rust had done the rest)
    -General rust and wear on the frame
    and on top of this I'd obviously overpaid.


    The seller, taking pity on my predicament, offered me a used set of Alexrims AT-400's for free which, he told me, consisted of a rear flip flop hub (had absolutely no idea what this meant at the time) The wheels and bike came with the advice that "it'd make a great fixie!" I willingly accepted the gift/challenge and rolled the bike back to my house.


    Back home I wasted no time dissembling the bike and prepping the frame and forks for paint.

    Saw someone on the forum using paint remover. As an after thought that might have been easier than the hours I spent sanding.

    While browsing various pictures online I came across a bike colour I quite liked:

    I did later realise this was Bianchi blue/green just the photo angle made it look a bit different. I got a couple of spray cans filled with a custom colour to match and painted my frame and forks.

    At this point I had to figure out a way to insert the headset cups back into the head tube (had a bicycle shop remove them and the bottom bracket earlier)

    A few googles and a trip to B&Q had me threading washers and nuts on to a massive threaded rod. Using this improvised tool the cups slid smoothly in and I could finish assembling the headset!

    Next came the freshly cleaned up and polished stem and drop bars. I decided to remove all the black paint from the stem, preferred the polished metal look.

    The next challenge came rather surprisingly. Apparently the axil in my rear hub was suppose to spin freely. Instead it seemed to be completely seized up with rust.

    Luckily this was quite easy to fix and purchasing a couple of new ceramic bearings was no problem. I resembled the hub with a healthy portion of grease and decided to put the wheels, brake and bar tape on to give me an idea of how the bike would look!

    Took what I've completed so far down to the bike shop this morning for them to fit a bottom bracket (I wasn't sure I could work out the correct sizing from what knowledge I had and decided it wasn't worth the risk of loss)

    My new seat arrived today at work too, a Charge Spoon in brown that should look nice with the bar tape.


    Behind you can see what I have been using to commute while I work on this project.

    In summary I'm really enjoying this experience. Spent a lot more money than I'd planned but not particularly regretting it and gained a lot of knowledge, enjoyment and really bizarrely specific bike tools.

    Will be collecting it from the bike shop tomorrow morning in a ready to ride condition. My first time on a fixed gear bike...

  • in General
    Avatar for ARudd

    Ah right, not too familiar with the forum layout yet. Thanks!

  • in General
    Avatar for ARudd

    Good Luck John88!

    I never really realised the threat bike thieves posed until I found this forum. Already invested in new locks and will be getting my bike marked/registered as soon as possible.

    Does anyone have any advice for locking up bikes in Cambridge city centre? places to avoid, times of day, etc. I'd assume it wouldn't be too bad considered the sheer number of tourists that are constantly around but would like to hear of anyone's experiences.

    cheers!

  • in General
    Avatar for ARudd

    Hello,

    First time poster. Been working on a fixed gear conversion the past few weeks and was looking for somewhere I could document my progress and get useful tips and help.

    I recently completed the coast to coast with a mate on what can only be called a sub optimal bicycle setup. Despite this I really enjoyed the experience and as I currently live in Cambridge and have lots of inspiration from all the great bikes I'm seeing everyday on my way to work, decided to start my own project.

Actions