35mhz

Most recent activity

• Wanted: WANTED: Front derailleur - Old School

  @35mhz started

  • 5 comments
  • 400 views

  @Vince replied
• Wanted: WANTED: Front derailleur - Old School

  in Wanted Adverts • 12 years, 2 months

  

  What I really need is one of these, it is a Suntor often branded Raleigh, it works in reverse, I.e it sprung to be in the big ring as default, it was std fare on 70's 80's Raleigh bikes, some one must have one lying about.

  See link for image

  www.35mhz.co.uk/suntor.JPG

• Wanted: WANTED: Front derailleur - Old School

  in Wanted Adverts • 12 years, 2 months

  

  I am looking for a front Derailler for my Carlton Restoration.

  Needs to be 28.6 Clamp on, bottom pull, suit 52t big ring, suit my 5 speed friction tube shifter

• Wheelbuilding / Wheel Building / Wheel build help

  in Mechanics & Fixin' • 12 years, 3 months

  

  I have just run this through spocalc, the qu what spoke lengths should I get for the back wheel, the front comes out out at 297.9mm so a 298mm sounds right, but on the rear its 294.4 and 293.5, should I just go for 294mm for both sides? seems spokes are in 2mm increments to buy

  Front Wheel Input Data Output Data
  N, total number of spokes 32 cross left length right length
  ERD, effective rim diameter 608.0 0 285.6 285.6
  OSB, offset spoke bed 0.0 1 287.1 287.1
  WL, width from center to left flange 34.1 2 291.5 291.5
  WR, width from center to right flange 34.1 3 297.9 297.9
  dL, left flange diameter 38.5 4 305.3 305.3
  dR, right flange diameter 38.5 3.00 297.9 297.9
  S, spoke hole diameter 2.4
  X, cross number (decimal allowed)(optional) 3.00
  WL_effective = W + OSB 34.1
  WR_effective = W - OSB 34.1

  Rear Wheel Input Data Output Data
  N, total number of spokes 36 cross left length right length
  ERD, effective rim diameter 608.0 0 282.8 281.9
  OSB, offset spoke bed 0.0 1 284.3 283.3
  WL, width from center to left flange 34.0 2 288.3 287.4
  WR, width from center to right flange 25.0 3 294.4 293.5
  dL, left flange diameter 44.0 4 301.7 300.8
  dR, right flange diameter 44.0 3.00 294.4 293.5
  S, spoke hole diameter 2.4
  X, cross number (decimal allowed)(optional) 3.00
  WL_effective = W - OSB 34.0
  WR_effective = W + OSB 25.0

• Wanted: Square Taper Double Chainset

  @35mhz started

  • 5 comments
  • 543 views

  @35mhz replied
• Wanted: Square Taper Double Chainset

  in Wanted Adverts • 12 years, 6 months

  

  Thanks Guys - Now sorted

  Geoffrey PM sent

• Wanted: Square Taper Double Chainset

  in Wanted Adverts • 12 years, 6 months

  

  I am after a Double Chainset to replace my Campagnolo Strada, which has finally turned its last as the Drive side taper is worn too much!!

  I do not need anything flash, and not hung up on any particular brand, but need serviceable unit with good tapers and threads.

  Anybody need a non drive side Strada Arm? 170mm

• Wanted: 3TTT Stem

  @35mhz started

  • 4 comments
  • 437 views

  @35mhz replied
• Wanted: 3TTT Stem

  in Wanted Adverts • 12 years, 8 months

  

  Regal - PM sent

• Wanted: 3TTT Stem

  in Wanted Adverts • 12 years, 8 months

  

  3TTT Stem, Old Style Silver

  What Have you?